Added 6th screen mounting pillar, improved kbd cable hole placement and screen mounting code

notebook_nueva/modelo.py

@@ -55,6 +55,7 @@ kbd_lower_pillars = (
 # Measured from top-left corner OUTSIDE
 mounting_pillar_positions = [
     (6, -6),
+    (6, -40),
     (120, -6),
     (170, -6),
     (width - 6, -6),

notebook_nueva/screen_mount.py

@@ -42,15 +42,10 @@ board_cutout = cq.Sketch().trapezoid(
 
 kbd_cable_hole = cq.Sketch().trapezoid(20, 9, 90, mode="a").vertices().fillet(1)
 
-# The last mounting pillar is handled specially
-x, y = mounting_pillar_positions[-1]
 mounting_pillars = (
     cq.Sketch()
-    .polygon([(0, 0), (width, 0), (width, -12), (0, -12), (0, 0)], mode="a")
-    .polygon(
-        [(x - 6, y - 6), (x - 6, y + 6), (x + 6, y + 6), (x + 6, y - 6), (x - 6, y - 6)]
-    )
     .push(mounting_pillar_positions)
+    .trapezoid(-12, 12, 90, mode="a")
     .circle(ti_radius, mode="s")
 )
 
@@ -72,25 +67,11 @@ def model():
         # of the inclined screen
         .placeSketch(cq.Sketch().trapezoid(1000, 1000, 90, mode="a"))
         .cutBlind(1000)
-        # Cut off viewport hole so we can see the screen
-        .workplaneFromTagged("slanted")
-        .placeSketch(viewport_cutout)
-        .cutBlind(-shell_t)
-        # Make hole for screen assembly so the whole screen fits
-        .workplaneFromTagged("slanted")
-        .workplane(offset=-shell_t, centerOption="CenterOfBoundBox")
-        # Left bezel is wider than right one, so this hole is displaced to the left
-        .center(-3, 0)
-        .placeSketch(screen_cutout)
-        .cutBlind(-scr_thickness)
         # Trim the top
         .workplaneFromTagged("mid_height")
         .workplane(offset=21)
         .placeSketch(cq.Sketch().trapezoid(1000, 1000, 90, mode="a"))
         .cutBlind(100)
-        # Fillet top of the object
-        .edges(">Z and |X")
-        .fillet(2.5)
         # Make bottom smaller to fit with base
         .faces(">X")
         .workplane(centerOption="CenterOfBoundBox")
@@ -112,6 +93,20 @@ def model():
             .fillet(3)
         )
         .cutBlind(-1000)
+        # Fillet top of the object
+        .edges("|X and >Z")
+        .fillet(3)
+        # Cut off viewport hole so we can see the screen
+        .workplaneFromTagged("slanted")
+        .placeSketch(viewport_cutout)
+        .cutBlind(-shell_t)
+        # Make hole for screen assembly so the whole screen fits
+        .workplaneFromTagged("slanted")
+        .workplane(offset=-shell_t, centerOption="CenterOfBoundBox")
+        # Left bezel is wider than right one, so this hole is displaced to the left
+        .center(-3, 0)
+        .placeSketch(screen_cutout)
+        .cutBlind(-scr_thickness)
         # Make it hollow
         .faces("<Z")
         # Can't be exactly shell_t because cq fails
@@ -122,11 +117,11 @@ def model():
         .placeSketch(board_cutout)
         .cutBlind(-6)
         # Make small hole for the keyboard cable
-        .faces(">Y")
-        .workplane(offset=-5, centerOption="CenterOfBoundBox")
-        .center(-width / 2 + 134, -44)
+        .faces("<Y")
+        .workplane(centerOption="CenterOfBoundBox")
+        .center(width / 2 - 175, -4)
         .placeSketch(kbd_cable_hole)
-        .cutBlind(-1000)
+        .cutBlind(-height / 2)
         # Pillars to join with bottom half
         .workplaneFromTagged("mid_height")
         .workplane(offset=-thickness / 2, centerOption="CenterOfBoundBox")